
OMGEXTRD D1
(1.75mm)
-
Direct Drive Extruder 2 modes.
-
Upgrade example model: ENDER 3 & V2 CR10
-
Net weight: 64g(no motor)
-
Double drive 1:3 Gear Ratio
-
E-steps:770 subdivision 16 step angle 0.9°
-
DM1-set kit include 36stepper motor
Notice: Direct drive
STL print slicing software (CURA, etc.) Retraction setting:
Suggested value: Speed 27mm/s ,Retraction Distance: 4mm
NOTE:Recently, there are 2 types of gears, which are shipped randomly, one with a diameter of 8mm, and a new one with a diameter of 8.4mm. Their E-STEP value settings are different. Please set the corresponding E-STEP value according to the gear diameter you received.
If using a 42 stepper motor, the step angle is 1.8°, the motor drive is 16 subdivisions, and the gear ratio is 1:3.If 8.4mm: E-STEP:363(8mm E-STEP:382)
If using a stepper motor at 36 pitch, the pitch angle is 0.9°, the motor drive is 16 subdivisions, and the gear ratio is 1:3.If 8.4mm:E-STEP: 726(8mm E-STEP:764)

E-STEP:
If using a 42 stepper motor, the step angle is 1.8°, the motor drive is 16 subdivisions, and the gear ratio is 1:3
E-STEP 363
If using a stepper motor at 36 pitch, the pitch angle is 0.9°, the motor drive is 16 subdivisions, and the gear ratio is 1:3
E-STEP: 726
1-spring presses filament pressure
2-and material of soft and hard filament
The e-step value should be tested and adjusted after installation
E-step: calculation method
Use 1/16 subdivision motor,
Stepper motor step angle = 1.8°,
The diameter of the gear is 8.4mm, the stepper
motor needs 16*200=3200 signals ofimpulse to turn 360°,
Filament moving length = gear circumference = 3,d = 3.14*8 = 26.376mm
How much e-step = filament displacement 1mm:
Calculation method: 3200/26.376 = 121 pulse signal.
E-step value is 121
Gear ratio is 1:3 - E-step value needs 3 times, that is 127.39*3=363 (theoretical value)
If you use 0.9° step angle - the electronic step value needs 2 times, that is 363*2=726 (theoretical value)
-
A Install the filament Press bearing using a Cross screwdriver
-
B Put in the middle part (see the picture), Insert the Spring and Screw in the fixing nut (M6)
-
C Install the Teflon bowden, Blue bowden clip is used to fix the Teflon tube(4mm) not move.

-
A Install stepper motor gear,Note the gear direction
-
B Install M3-6 4pcs screws (don’t tighten frist)
-
C Adjust the position of the stepper motor gear (as shown in the picture)

-
A Check Drive gear 2 precision mini bearings up and down is installed (pre-installed in factory)
-
B Adjust the gear gap, Free and relaxed rotation is the standard.Then tighten the M3-6 *4pcs screws fixed with the motor

-
A Adapter part ID: v2-M6 is suitable for ENDER 3 V2. Please check step 5
-
B Adapter part ID: 10M6A suitable for ENDER 3 & CR10 etc. Ps: Adaptation part ID10M6A is also compatible with E3D V6 Hotend
A Combination installation 10M6A
B Installation with extruder
C When connecting with the hot end, leave a gap of 0.5-1mm
D Use a wrench to adjust the positioning nut. Positioning as shown in the picture C

-
A Insert and install Teflon tube
-
B Cut the Teflon tube, the Teflon tube grows out of the throat 0.5-1mm as shown in the picture, the function is to ensure that the Teflon tube does not move, the extruder retracts the filament to keep the Teflon tube and the nozzle without gaps
-
C Install heating block and nozzle
-
D Install the hot end and printer mounting plate



